散射对高温气体-碳黑颗粒混合物辐射传输的影响

基于全光谱k分布(Full spectrum k distribution,FSK)模型、MIE理论和有限体积法(Finite volume method,FVM),构建了均温、均质辐射参与性气体-碳黑颗粒混合物介质热辐射传输模型,并分析了碳黑不同尺寸、不同体积浓度以及介质不同路径长度和不同温度条件下,因忽略碳黑颗粒散射所导致的介质热辐射传输特性(如辐射热流、辐射源项)的计算误差。研究结果表明:体积分数不变,增大粒径,计算误差呈现出先增大后减小的趋势;数密度不变,增大粒径,或者粒径不变,增大体积分数,均将使得计算误差相应增大;粒径、体积分数不变,增大路径长度,或者升高介质温度,均将增大计算误差。通常对于含有大颗粒、高碳黑浓度的辐射参与性气体-碳黑颗粒混合物介质,碳黑颗粒散射不能忽略。     

钛合金表面抗激光涂层损伤特性及热效应影响研究

实验研究了钛合金和高反射型陶瓷涂层材料抗连续型激光烧蚀的损伤及温度分布特性，并从热效应影响角度对比分析了二者在抗激光损伤效果方面的差异性。研究结果表明：相比于钛合金，高反射型陶瓷涂层材料能有效增强钛合金基底抗激光损伤的能力；在同等激光功率密度辐照下，陶瓷涂层材料能有效提升钛合金基底耐受激光辐照的时间长度。实验结果表明该陶瓷涂层材料的激光损伤阈值比钛合金高约5.8倍。实验发现陶瓷涂层温升速率高于钛合金，但由于陶瓷材料具有较高的反射特性，以及良好的热吸收和热传导特性，因此能使由激光辐照产生的热量在其表面较快地扩散，而降低向基底方向传导的程度，最终提升陶瓷涂层的抗激光损伤阈值。     

Modeling the effects of green alternative on heat island mitigation of a meso level town,West Bengal,India

Urban heat island (UHI) is emerged as a ubiquitous phenomenon that affects the outdoor thermal comfort. Hence urban microclimatic studies using numeric simulation software to find out adaption strategies are attracting the great attention of researchers and policymaker. Number of scientists carried out their research on this topic using different tools and technique whereas ENVI-met model is the most widely used simulation tools. The present study intended to examine the implication of green infrastructure of the town on enhanced microclimatic condition and to evaluate the best suitable mitigation strategy modelling cool city with ENVI-met software (V4). Five greening condition such as existing UHI condition (C1), 100% greening of roof (C2), 100% greening of roof and walls (C3), 50% greening of roof and walls (C4) and: Plantation at suitable area with 50% greening of roof and walls (C5) have been taken into consideration for the microclimate simulation for all three selected sites. Among these five conditions, C3 for the open mid-rise and compact low-rise, C5 for the open low-rise are identified as one of the most suitable strategies which can reduce the air temperature of peak hours by 2.6 °C, 1.33 °C and 1.87 °C respectively. These models are validated by simple linear regression between simulated and existing air temperature in case of existing UHI condition (C1) and in all the cases coefficient of determination value is high such as for open mid-rise, compact low-rise and open low-rise, it is 0.92, 0.92 and 0.75 respectively. Therefore it can be concluded that the application of those strategies can improve the urban thermal environment as well as the outdoor thermal comfort of English bazaar Town and its surroundings.     

弱引力下小行星动量驱动机器人的可控跳跃行为

以小行星表面着陆探测为背景,提出一种动量驱动机器人(MoRo)以满足弱引力复杂环境下的探测需求。该机器人利用弱引力环境下的摩擦和碰撞特性,通过主动辨识环境参数,规划和控制动量轮以产生期望的驱动力矩,完成可控性跳跃及腾空后的稳定拍照等任务。首先,基于MoRo的动量轮刹车机构特性,分析了MoRo在弱引力环境下的跳跃机理并对其跳跃方式进行了规划;接着考虑动量轮驱动机构三闭环伺服系统的非线性特性,基于Herze碰撞模型和Karnopp摩擦模型建立了MoRo在小行星表面的跳跃行为动力学模型;其次,使用机器学习算法建立环境参数和MoRo运动的函数关系,并基于环境参数规划动量轮转速实现跳跃距离和腾空高度的可控。最后,通过数值仿真校验了MoRo跳跃规划方法和控制方法的可行性。     

R141b在圆形微通道内的沸腾换热实验研究

为提高换热强度、解决设备内部高热流密度散热问题,采用实验方法研究R141b在不同直径(D=0.5mm和1.0mm)水平圆形微通道内的沸腾换热特性,分析了热流密度(q=2.0kW/m~2～47.6kW/m~2)、质量干度(x=0～0.6)、质量流速(G=111.11kg/(m~2·s)～333.33kg/(m~2·s))的变化对平均传热系数h的影响,探究不同情况下影响沸腾换热的主导因素。实验研究表明:平均传热系数h随热流密度q的增加而减小,在不同范围内减小速率有明显差异;热流密度q=2kW/m~2～5kW/m~2时质量流速G对平均传热系数h影响较明显,热流密度较高时质量流速G对换热影响很小;在质量流速G=111.11kg/(m~2·s)～333.33kg/(m~2·s),质量干度x0.3时,平均传热系数h随质量干度x增加而明显下降,在设计微通道换热器时应尽量使R141b处于初始沸腾阶段以获得更好换热效果,并采取一定措施预防干度过高引起的换热恶化。     

运载火箭推进剂复杂流动传热问题数值模拟中的模型简化方法

在运载火箭改进优化或新型运载火箭设计过程中,会遇到各种复杂的流动与传热问题。按照真实产品和物理过程直接建立的数值计算模型过于复杂,不同尺度的结构、流动与传热、长时间的飞行过程相互耦合,出现计算时间太长(数年)、收敛困难、程序调试困难等问题。针对初始条件复杂、飞行过程复杂、边界条件复杂3类具体问题,总结了3种相应的模型简化方法,分别是工程经验法、极限参数法、低维近似法,为推进剂复杂流动与传热的数值模拟提供参考。     

Review and propositions for the sliding/impact wear behavior in a contact interface

A thermal-solid-liquid complex operational environment induces structural interface developing a typical coupling sliding/impact wear behavior. It results in contact damage until systems fail, which may cause significant economic losses and catastrophic consequences. The key point of solving this problem is to reveal the coupling damage mechanism of the sliding/impact behavior in typical systems and life characterization under a complicate evolving environment. This has been a hot topic in the area of mechanical reliability. The main work in this paper can be concluded as follows. Firstly, the main industries in which the “sliding/impact behavior” takes place have been introduced. Then, existing studies on the wear mechanism and degree analysis are presented, which includes surface morphology analysis, wear debris analysis, and wear degree measurement. Meanwhile, existing problems in theoretical modeling and experiments in current research are summarized, so as to point out a bright direction for future research on wear prediction. They include interface contact modeling, mathematic coupling mechanism modeling, wear equation establishment, and wear life characterization, which can provide some new ideas for improving the existing studies on the sliding/impact wear behavior.     

现代激励理论在规范地方政府行为中的作用研究

分析现代激励理论在研究地方政府行为中的作用，并运用现代激励理论提出了规范地方政府经济行为的若干建议。     

General relativistic radiation hydrodynamics: Mixed-frame approach

I show how general relativistic 3D radiation hydrodynamic equations can be derived from the tensor formulation. Radiation quantities are differentiated with respect to the fixed coordinates while the interaction between matter and radiation is described by the comoving frame quantities. The formulation is covariant, and can be applied to any coordinates or spacetime; I show the derivation for the Schwarzschild spacetime as an example.     

圆柱齿轮齿廓偏差及螺旋线偏差精度控制研究

在齿轮加工过程中,热处理变形是影响齿轮精度的主要原因之一.通过分析CA457桥从动圆柱齿轮在渗碳淬火热处理中齿廓偏差、螺旋线偏差的变化数据,得出齿廓偏差、螺旋线偏差的变形规律.根据渗碳淬火后基圆半径和螺旋角的变形均呈增大趋势,修改加工刀具的设计齿廓和齿轮的设计螺旋线,降低热处理前产品的工艺精度,保证了热处理后产品的合格率.在创造良好经济效益的同时也为同类产品提供了设计依据.